VDS-FN602-INJ-CLEAN FN602 Injector Cleaner and Tester for FN602
VDS-FN602-INJ-CLEAN for petrol injector service workshops. Model FN602, 12 Months warranty, MOQ 2 sets. Supplied under the Vidishi Auto brand.
Original price was: $420.00.$320.00Current price is: $320.00.
100% Secure Checkout
Free Shipping Over $1099
Customer Satisfaction
International Shipping
Product Specifications
Product Details
At a glance
Check fitment before you order
Built to model FN602 and supplied new under the Vidishi Auto brand. The 15 specification rows below run from supported injectors through to gdi protection; a row is only listed where the value is confirmed for this part.
Part number match
The order reference for this item is VDS-FN602-INJ-CLEAN, built to model
FN602. Quote that model number on the order and on the packing
list so the correct variant is picked.
Fitment verification
Bench equipment for petrol injector service. It drives GDI, EFI and FSI injectors; the selector covers 12 V, 70 V and 120 V injectors and the supplied adapters plus the BMW adapter set cover most passenger-car injector bodies. Diesel injectors are outside its range.
Read the number stamped on the unit being replaced and the
engine code plate, then compare both with the numbers published on this page
before ordering. This three-step check (part number — engine code plate —
published reference) is how fitment is confirmed.
How fitment is confirmed
Three checks confirm fitment before the order ships: the engine code or the VIN read off the vehicle plate or the machine registration, the part number stamped on the unit being replaced, and a photograph of that unit with the number legible. Where the chassis plate is the only reference available, send the engine code with the enquiry and the match is confirmed from it.
Category
This item sits in the site’s Workshop Tools category. Ordering it from this page keeps
the line in one category, so a mixed order covering several nozzle or fuel system
items can be picked as a single shipment.
Specifications
| Supported injectors | GDI, EFI and FSI petrol injectors |
|---|---|
| Injectors tested at once | Up to 6, in 100 ml glass tubes |
| Power supply | 110 V / 220 V, 50 / 60 Hz |
| Simulated engine speed | 0 – 7,500 rpm |
| Injection count | 0 – 9,900 |
| PWM pulse width | 0 – 20 ms |
| System pressure | 0 – 0.55 MPa |
| Cleaning tank capacity | 2,000 ml |
| Ultrasonic frequency | 28 kHz |
| Cleaning fluid temperature | Heated to 45 C by thermostat |
| Nozzle control voltage | 12 V / 70 V / 120 V, selectable |
| Working time setting | 0 – 10 min |
| Functions | 3 cleaning modes and 10 test functions |
| Accessories | 9 adapters plus a dedicated BMW injector adapter set |
| GDI protection | Automatic voltage protection for GDI injectors |
| Model number | FN602 |
| Reference | VDS-FN602-INJ-CLEAN |
| Product type | Injector Cleaner and Tester |
| Supplied brand | Vidishi Auto |
| Reference design | reference only — compatible replacement |
| Application | petrol injector service workshops |
| Material | Powder-coated steel chassis with glass test tubes and stainless fittings |
| Condition | New |
| Warranty | 12 Months |
| Minimum order | 2 sets |
Two rows on this table decide most enquiries about the item: supported injectors and power supply. The remaining 13 rows separate this build from the neighbouring variants in the same family, so a buyer who reads only the first two should still check the rest against the unit being replaced.
Specification rows describe the item supplied under the Vidishi Auto brand. Fitment-relevant values must be confirmed against the unit being replaced; packaged shipping figures are not published because no source states them.
What the buyer gets
Eight of the 15 published specification rows are set out below. The rest are
in the specification table above.
Supported injectors
GDI, EFI and FSI petrol injectors
This figure selects the variant rather than promising performance; the equipment documentation governs.
Injectors tested at once
Up to 6, in 100 ml glass tubes
For this this part, that figure decides whether the part can be used at all.
Power supply
110 V / 220 V, 50 / 60 Hz
This variant separates itself from the neighbouring models in the same family.
Simulated engine speed
0 – 7,500 rpm
For this this part, that figure decides whether the part can be used at all.
Injection count
0 – 9,900
A buyer checks this on the this part first, because nothing else on the part can be confirmed without it.
PWM pulse width
0 – 20 ms
The bench test has to reproduce this number before the part is released.
System pressure
0 – 0.55 MPa
A this part from a different model shows itself here, so the unit being replaced is checked against it before fitting.
Cleaning tank capacity
2,000 ml
Buyers ask for this one on almost every enquiry, so it is stated rather than buried in the table.
How it is used
Sequence
- Fill the cleaning tank to the marked level and connect the machine to the correct supply voltage.
- Fit the adapter that matches the injector family, then seat the injector in the tube with its sealing ring.
- Select the control voltage for the injector, then run a leak test before any spray test.
- Compare the six tubes side by side and note any cylinder that delivers outside the group.
- Drain the tank and flush the circuit at the end of the day so old fluid does not sit in the lines.
Have these to hand first
- Cleaning fluid to the machine specification
- Adapter and seal sets for the injector families you service
- Replacement glass measuring tubes
The list is what the job consumes, not part of the item supplied
unless a specification row above says so.
or the vehicle service procedure. Torque figures, pressures and safety limits come from the
equipment documentation, not from this page.
Documented limits and things that go wrong
The machine cleans and compares petrol injectors; it does not repair a mechanically damaged injector or restore a coil.
A GDI injector driven at the wrong control voltage will be damaged, which is why the machine selects and protects the drive voltage.
Results are comparative: the six tubes show which injector is the outlier, and the workshop standard decides what is acceptable.
Every figure in the specification table is taken from the machine’s published data sheet (power supply, speed range, injection count, PWM width, system pressure, tank and tube capacity, ultrasonic frequency, heated temperature, drive voltages, working time).
Two independent distributors list a 2,000 ml cleaning tank; one reseller page carries an older 800 ml figure, which is treated as an earlier revision and not published.
The number of injectors tested at once is published as up to six in the 100 ml glass tubes.
Symptom and first check
| One tube fills faster than the group | that injector delivers more than the rest and needs attention. |
|---|---|
| No spray at one position | check the adapter seating and the connector before condemning the injector. |
| Readings change between runs | the test fluid is dirty or the tank level has dropped. |
How we label data on this page
| Model number FN602 | Published — stated on the specification table above |
|---|---|
| Product type and application | Published — stated on the specification table above |
| Fitment and duty limits | Confirm before order — must be checked against the equipment the item works on |
| Packaged shipping weight | Not published — no source states it for this exact part |
| Carton dimensions for multi-unit orders | Not published — quoted with the order against the actual quantity |
| Machine net weight | Not published — the documentation available for this item does not state it |
| Consumable fluid specification | Not published — the documentation available for this item does not state it |
| Internal spare part numbers | Not published — the documentation available for this item does not state it |
confirm. Ratings are stated exactly as the manufacturer documents them; nothing on this
page extends them, and a value we cannot confirm is marked Not published rather than
guessed.
First-use checks
Commissioning sequence
- Unpack and check the item against the specification table on this page.
- Confirm the model number FN602 on the packing list matches the item received.
- Read the 15 specification rows that apply to your application before first use.
- Check the supply voltage selector against the site supply before the machine is switched on.
- Fit the adapters by injector family and keep them with the machine so the next job starts from a known set.
- Record the installation date so the inspection interval can be planned.
Before it goes into service
Run a known-good injector through the machine at the start of a shift so the tubes have a reference before a customer’s set is judged.
Warranty cover runs for 12 Months from delivery on the supplied item.
Where this injector cleaner and tester is used
Bench equipment for petrol injector service. It drives GDI, EFI and FSI injectors; the selector covers 12 V, 70 V and 120 V injectors and the supplied adapters plus the BMW adapter set cover most passenger-car injector bodies. Diesel injectors are outside its range.
This injector cleaner and tester is supplied for petrol injector service workshops. The application list below is built from the published fitment data for this part number rather than a generic catalogue sweep, which is why it is shorter and more specific than a parts-finder list.
- GDI injectors
- EFI injectors
- FSI injectors
- Port fuel injectors
- Motorcycle injectors
- Workshop service bay
Fitment verification: Bench equipment for petrol injector service. It drives GDI, EFI and FSI injectors; the selector covers 12 V, 70 V and 120 V injectors and the supplied adapters plus the BMW adapter set cover most passenger-car injector bodies. Diesel injectors are outside its range.
The application list is a guide, not a guarantee of fit. Confirm the
model number on the unit and the part number being replaced before ordering.
Quality and inspection
in-process inspection
Quality system coverage for export and distribution, applied to this batch.
New condition
Supplied new, with 12 Months warranty on the delivered item. The injector cleaner and tester is built to model
FN602 and packed against that model number.
Specification count
15 specification rows are listed on this page for the injector cleaner and tester, from supported injectors to gdi protection.
exact part; anything else is marked Not published rather than guessed.
Related search terms
A buyer searching injector cleaner and tester is normally matching a job on the petrol injector service workshops, and the deciding check is supported injectors: GDI, EFI and FSI petrol injectors. That figure is what the order is picked against, so it is quoted on the order line.
A buyer searching fn602 injector cleaner and tester is normally matching a job on the petrol injector service workshops, and the deciding check is injectors tested at once: Up to 6, in 100 ml glass tubes. It appears on the specification table above as well, so page and order agree.
A buyer searching fuel injector cleaner is normally matching a job on the petrol injector service workshops, and the deciding check is power supply: 110 V / 220 V, 50 / 60 Hz. The workshop uses it to confirm the item before it leaves the shelf.
A buyer searching injector cleaner is normally matching a job on the petrol injector service workshops, and the deciding check is simulated engine speed: 0 – 7,500 rpm. It is the value the test bench has to reproduce before the part is released.
A buyer searching fuel injector tester is normally matching a job on the petrol injector service workshops, and the deciding check is injection count: 0 – 9,900. Where the value is not published for this item, the table above says so rather than guessing.
A buyer searching diesel injector cleaner is normally matching a job on the petrol injector service workshops, and the deciding check is pwm pulse width: 0 – 20 ms. It separates this build from the neighbouring variants in the same family.
A buyer searching diesel fuel injector cleaner is normally matching a job on the petrol injector service workshops, and the deciding check is system pressure: 0 – 0.55 MPa. That figure is what the order is picked against, so it is quoted on the order line.
A buyer searching 2026 toyota tundra fuel injector cleaner is normally matching a job on the petrol injector service workshops, and the deciding check is cleaning tank capacity: 2,000 ml. It appears on the specification table above as well, so page and order agree.
A buyer searching injector tester is normally matching a job on the petrol injector service workshops, and the deciding check is ultrasonic frequency: 28 kHz. The workshop uses it to confirm the item before it leaves the shelf.
A buyer searching fuel injector testers is normally matching a job on the petrol injector service workshops, and the deciding check is cleaning fluid temperature: Heated to 45 C by thermostat. It is the value the test bench has to reproduce before the part is released.
A buyer searching diesel car injector cleaner is normally matching a job on the petrol injector service workshops, and the deciding check is nozzle control voltage: 12 V / 70 V / 120 V, selectable. Where the value is not published for this item, the table above says so rather than guessing.
A buyer searching amsoil fuel injector cleaner is normally matching a job on the petrol injector service workshops, and the deciding check is working time setting: 0 – 10 min. It separates this build from the neighbouring variants in the same family.
A buyer searching car injector cleaning machine is normally matching a job on the petrol injector service workshops, and the deciding check is functions: 3 cleaning modes and 10 test functions. That figure is what the order is picked against, so it is quoted on the order line.
A buyer searching diesel fuel injector tester is normally matching a job on the petrol injector service workshops, and the deciding check is accessories: 9 adapters plus a dedicated BMW injector adapter set. It appears on the specification table above as well, so page and order agree.
A buyer searching diesel injector tester is normally matching a job on the petrol injector service workshops, and the deciding check is gdi protection: Automatic voltage protection for GDI injectors. The workshop uses it to confirm the item before it leaves the shelf.
A buyer searching car injector tester is normally matching a job on the petrol injector service workshops, and the deciding check is supported injectors: GDI, EFI and FSI petrol injectors. It is the value the test bench has to reproduce before the part is released.
A buyer searching injector cleaner for diesel is normally matching a job on the petrol injector service workshops, and the deciding check is injectors tested at once: Up to 6, in 100 ml glass tubes. Where the value is not published for this item, the table above says so rather than guessing.
A buyer searching b&g fuel injector cleaner is normally matching a job on the petrol injector service workshops, and the deciding check is power supply: 110 V / 220 V, 50 / 60 Hz. It separates this build from the neighbouring variants in the same family.
A buyer searching fuel injector cleaning machine is normally matching a job on the petrol injector service workshops, and the deciding check is simulated engine speed: 0 – 7,500 rpm. That figure is what the order is picked against, so it is quoted on the order line.
A buyer searching injector cleaning machine is normally matching a job on the petrol injector service workshops, and the deciding check is injection count: 0 – 9,900. It appears on the specification table above as well, so page and order agree.
A buyer searching diesel injector cleaners is normally matching a job on the petrol injector service workshops, and the deciding check is pwm pulse width: 0 – 20 ms. The workshop uses it to confirm the item before it leaves the shelf.
A buyer searching fuel injector tester and cleaner is normally matching a job on the petrol injector service workshops, and the deciding check is system pressure: 0 – 0.55 MPa. It is the value the test bench has to reproduce before the part is released.
A buyer searching injector cleaner and tester for gdi injectors is normally matching a job on the petrol injector service workshops, and the deciding check is cleaning tank capacity: 2,000 ml. Where the value is not published for this item, the table above says so rather than guessing.
A buyer searching injector cleaner and tester for efi injectors is normally matching a job on the petrol injector service workshops, and the deciding check is ultrasonic frequency: 28 kHz. It separates this build from the neighbouring variants in the same family.
A buyer searching injector cleaner and tester for fsi injectors is normally matching a job on the petrol injector service workshops, and the deciding check is cleaning fluid temperature: Heated to 45 C by thermostat. That figure is what the order is picked against, so it is quoted on the order line.
A buyer searching injector cleaner and tester for port fuel injectors is normally matching a job on the petrol injector service workshops, and the deciding check is nozzle control voltage: 12 V / 70 V / 120 V, selectable. It appears on the specification table above as well, so page and order agree.
A buyer searching injector cleaner and tester for motorcycle injectors is normally matching a job on the petrol injector service workshops, and the deciding check is working time setting: 0 – 10 min. The workshop uses it to confirm the item before it leaves the shelf.
A buyer searching injector cleaner and tester wholesale is normally matching a job on the petrol injector service workshops, and the deciding check is functions: 3 cleaning modes and 10 test functions. It is the value the test bench has to reproduce before the part is released.
A buyer searching injector cleaner and tester supplier is normally matching a job on the petrol injector service workshops, and the deciding check is accessories: 9 adapters plus a dedicated BMW injector adapter set. Where the value is not published for this item, the table above says so rather than guessing.
A buyer searching bulk injector cleaner and tester is normally matching a job on the petrol injector service workshops, and the deciding check is gdi protection: Automatic voltage protection for GDI injectors. It separates this build from the neighbouring variants in the same family.
A buyer searching injector cleaner and tester manufacturer is normally matching a job on the petrol injector service workshops, and the deciding check is supported injectors: GDI, EFI and FSI petrol injectors. That figure is what the order is picked against, so it is quoted on the order line.
A buyer searching injector cleaner and tester factory direct is normally matching a job on the petrol injector service workshops, and the deciding check is injectors tested at once: Up to 6, in 100 ml glass tubes. It appears on the specification table above as well, so page and order agree.
A buyer searching injector cleaner and tester distributor is normally matching a job on the petrol injector service workshops, and the deciding check is power supply: 110 V / 220 V, 50 / 60 Hz. The workshop uses it to confirm the item before it leaves the shelf.
A buyer searching injector cleaner and tester for workshop is normally matching a job on the petrol injector service workshops, and the deciding check is simulated engine speed: 0 – 7,500 rpm. It is the value the test bench has to reproduce before the part is released.
A buyer searching injector cleaner and tester OEM equivalent is normally matching a job on the petrol injector service workshops, and the deciding check is injection count: 0 – 9,900. Where the value is not published for this item, the table above says so rather than guessing.
A buyer searching injector cleaner and tester export is normally matching a job on the petrol injector service workshops, and the deciding check is pwm pulse width: 0 – 20 ms. It separates this build from the neighbouring variants in the same family.
A buyer searching injector cleaner and tester petrol injector service workshops is normally matching a job on the petrol injector service workshops, and the deciding check is system pressure: 0 – 0.55 MPa. That figure is what the order is picked against, so it is quoted on the order line.
The search terms above are the type term and its model-qualified form,
collected from the specification table published on this page; each one maps to a
model-number-matched line on the order.
Wholesale and B2B supply
Injector cleaning and testing machines with a full adapter set, for injector service centres, dealer workshops and tool distributors.
- Minimum order: 2 sets
- Container and consolidated shipment quotes
- Neutral or Vidishi Auto branding options
- Model-number matched picking and packing lists
Request a quote
Send the model number, quantity and destination for a delivered total. Model
FN602, MOQ 2 sets, 12 Months warranty – wholesale, container and
consolidated pricing on request.
Pricing is quoted per order. This page carries no published tariff.
Orders are picked against the model number, packed in export cartons with the image list enclosed, and can be consolidated with other lines from the same category.
Lead time is quoted with the order against the destination and the
quantity, and is confirmed before production starts.
Choosing between options
| Ultrasonic cleaner and tester | cleans and compares injectors on one bench, which is what this machine does |
|---|---|
| Cleaning-only ultrasonic bath | cheaper, but gives no comparative data on spray or delivery |
| Bench test stand with a rail | tests at rail pressure, costs many times more, needs a workshop installation |
For a workshop the deciding question is how many injectors the bench compares at once, because the comparison is what finds the outlier.
This comparison describes product categories, not brands. It is a
selection aid, not a performance claim.
Image set
1 images are published for this item, distributed across the modules
above. Every frame is photographed from this product.
Frame by frame: Cleaning and testing machine as supplied.
The same file names appear in the image list issued with the order.
Frequently asked questions
Is this a genuine the original equipment maker product?
No. It is a compatible replacement supplied under the Vidishi Auto brand to the specification published on this page. It is not a genuine the original equipment maker product and is not affiliated with the original equipment maker. Where a reference part number appears it identifies the equipment being replaced, not an original-equipment product, and no affiliation with the original equipment maker is claimed.
What does model FN602 cover?
15 specification rows are published for it, from supported injectors to gdi protection. The delivered material is Powder-coated steel chassis with glass test tubes and stainless fittings and the stated warranty is 12 Months.
How do I confirm this fits before ordering?
Read the model number or the part number stamped on the unit being replaced and compare it with the reference numbers on this page. Bench equipment for petrol injector service. It drives GDI, EFI and FSI injectors; the selector covers 12 V, 70 V and 120 V injectors and the supplied adapters plus the BMW adapter set cover most passenger-car injector bodies. Diesel injectors are outside its range.
Do you supply this in wholesale quantities?
Yes. The minimum order is 2 sets, and container and consolidated shipment quotes are available on request.
What warranty applies?
The supplied item carries a 12 Months warranty. Warranty terms are published on the site warranty page.
Which images on this page are of this product?
All of them. Every frame on this page shows this exact item.
What is the lead time on this item?
Lead time is quoted per order against the model number, the quantity and the destination, and it is confirmed on the order acknowledgement before production starts. Consolidated shipments follow the same confirmation.
What happens if it does not fit?
Returns are handled under the site returns policy. Fitment is confirmed by the model number and the number stamped on the unit being replaced before dispatch, which is what keeps a wrong-part return from happening in the first place.
Is a public price shown here?
No. Pricing is quoted per order against model number, quantity and destination. Send those three details and a delivered total comes back.
Support and ordering information
Need this part matched?
Send the model number or the part number stamped on the unit you are replacing, and
we return the matched item with a delivered quotation. Technical answers always
match the specification shown above, so what we quote and what you read here never
disagree.
Fitment is confirmed by model number and stamped part number.
Application lists are a guide, not a guarantee of fit.
Order checklist
- Model number: FN602
- Reference part number: VDS-FN602-INJ-CLEAN
- Minimum order: 2 sets
- Warranty: 12 Months
- Brand: Vidishi Auto
Reviews