PE-V2LA1 Poultry Equipment Automatic Type -dip

Specifications

The parameters above cover what buyers compare when searching oem poultry equipment.

Compatibility & fitment guide

How to identify the correct unit: locate the reference number stamped on your original component or in the vehicle parts catalogue, then cross-check it against the number below before ordering. Trim and market variants exist for many applications, so the short check is worth the minute before checkout.

How to identify & confirm fitment in 4 steps

1. Locate the OE / reference number on your old part or in the vehicle parts catalogue.
2. Match it to PE-V2LA1 shown on this page.
3. Send your VIN and engine code plate so our team runs an exact-fit check.
4. Receive fitment confirmation before we dispatch your order.

Cross-reference coverage for poultry equipment fitment is listed above; confirm your VIN before ordering.

Product overview

A direct-fit compatible replacement referenced by PE-V2LA1 for the applications listed in the fitment block.

Feature highlights

Buyers searching egg breeding equipment and laying hen cage look for the strengths listed here: direct fit, verified reference and wholesale packing.

Applications & use cases

The fitment block above lists the markets and model families this reference is stocked for, so buyers can match demand without re-checking every listing.

Technical insights

Deep dive. Wet litter under a line is the symptom that pays for the diagnostic visit: a leaking nipple usually has worn stem seals or grit holding the valve open, and continuous drips raise ammonia and disease pressure in the house. Isolated dead nipples point to clogging from unfiltered water, implicating the filter element or the recoil-flush routine rather than the nipples themselves. Birds crowding one section while ignoring another signals a line height or pressure mismatch for their age. A sagging line indicates winch or suspension wire problems, and erratic pressure at the level display tube traces to the regulator, not the pipe run.

Deep dive. Hang lines level with winches at 3 m spacing and set nipple height by bird age, since both too-high and too-low placement causes spilled water and skeletal stress in young flocks, a documented failure mode. Set regulator pressure for the day-age: low pressure at brooding, rising as birds grow, within the documented 10-13 kPa band. Fit the front assembly with filter, water meter, and doser where the operator reaches it daily. Flush every line before flock placement, and tension the anti-roost wire so birds cannot perch above the pipes and foul the drinking system.

Field note. Daily tasks are short: read the water meter for flock health trending, check the level tube, and recoil-flush lines at the regulator to push sediment out. Clean or replace the filter element on schedule because it protects every nipple downstream. Between flocks, flush and descale the whole circuit, inspect seals on the doser and regulator, and replace nipples that drip under static pressure. Verify winch balance so lines lift evenly, and examine PP drip cups for cracks during house turns. Stainless stems documented beyond 10 years of service still depend on water treatment, so manage hardness and biofilm at the source.

Application context. Compare five practical points. Nipple spec: 360-degree stainless stems with double seals outlast plastic-bodied equivalents and suit variable water quality. Density: 12 or 15 nipples per 3 m determines birds per drinker and stocking flexibility. Regulator: recoil-flush capability keeps lines clean without disassembly. Front assembly: insist on filter plus water meter plus doser as one unit. Structure: hot-dip galvanized pipe at 275 g/m2 zinc and a 1,500 lb winch suspension define durability on documented listings. Verified system service lives of 10-15 years justify comparing these specification lines rather than the lowest pipe price alone.

Field note. Hard certification specific to nipple drinking lines is limited, and verified listings lean on factory quality systems, with ISO 9001:2008 certification appearing on documented manufacturer profiles alongside CE marks on related house equipment. The material specifications that matter are verifiable from datasheets: 275 g/m2 zinc coating on galvanized pipe, 304 stainless steel components, and PP cup material. Customs classification for poultry-keeping machinery parts falls under HS code 8436.91. Buyers should request the zinc-coating certificate and material declarations rather than relying on generic conformity claims, since these documents anchor the durability argument of the whole line.

Field note. This equipment class serves floor-raised broiler houses primarily, with layer and breeder operations using the same drinking architecture. Integrators building turnkey houses buy drinking lines together with pan feeding, silo, ventilation, and cooling pad systems sized to the shed. Buyer profiles split three ways: poultry farm contractors order by house drawing and nipple count; farm owners upgrading from bell drinkers prioritize dry litter and water metering; equipment distributors stock nipples, cups, regulators, and winches as consumable line items. Water quality, stocking density, and climate control around the line decide results as much as the hardware itself.

Application context. In a dip-cup drinking line the wear list is long: cup assemblies and their valve pins, rubber seals and O-rings, filter cartridges, the dosing pump's suction tube, and the regulator spring. Standard practice is a filter rinse every two days, a full line flush within an hour or two of any medication, and strip-down of the doser and regulator between flocks. Replace seals and any sticking cups as a complete set each flock so water flow stays uniform from line head to tail.

Application context. PVC line sections crack under frost and turn brittle under sustained sunlight, so store spare pipe flat under cover with end caps taped on to keep dust out of the bore. Before an empty house sits idle for days, drain every pipe, the doser, and the filter completely, and back the regulator screw off to zero water column so the internal spring rests unloaded. Transport cups and nipples boxed separately from pipe so loose parts cannot score the pipe interior.

Deep dive. Cut pipe with a dedicated PVC pipe cutter rather than a saw, because saw chips migrate into cups and cause persistent drips; note that PVC-U solvent cement is highly flammable, so keep it well away from heat sources during assembly. Rig lines level using nylon rope and winches, keep the doser's suction head off the bucket bottom, and after plumbing, flush each single line end-valve-first until the water runs clear, then set the working pressure by the regulator's sight-glass column.

Deep dive. Water chemistry shifts with the seasons: aim for pH roughly 6.2 to 6.8, because high pH blunts sanitizers while low pH can corrode metal components and upset bird gut health. Summer demand can exceed well and pump capacity on the hottest days, so size the supply before peak arrives. Warm water breeds biofilm and algae, which means more frequent flushing in hot months; in winter, frozen lines are the top failure mode, hence strict drain-down whenever the house empties.

Field note. Batch buying for poultry equipment is really spare-ratio planning: stock spare dip cups, valve pins, and filter cartridges at a defined percentage of total line length, because a single sticking pin wets litter across a whole bay. Ask the supplier which documents ship with the order – dimensional drawings, material declarations for the PVC, and the doser user manual – and inspect incoming pipe for consistent wall thickness and square, clean cuts. Log batch numbers against house and line positions.

Field note. Configuration differences catch many buyers: nipple-only lines versus dip-cup versions, and pipe diameters such as 25 mm systems, cannot be mixed and matched without the correct saddles and adapters. Working pressure is set by the regulator's sight-glass column height, not by feel or guesswork. The documented pitfalls: flushing several lines simultaneously drops pressure and defeats the flush, disassembling the doser with tools is prohibited by manufacturers, and thick or poorly soluble medicines clog both the doser and the cups.

Workshop note. Verified nipple drinking lines deliver 12 or 15 nipples per 3 m pipe section, with each nipple serving roughly 8-12 broilers.

Application note. Nipple valve stems are corrosion-resistant stainless steel with 360-degree lower-stem actuation and a double-seal structure; documented service life exceeds 10 years.

Workshop note. Line pressure regulators on verified systems hold about 10-13 kPa and provide recoil flushing that raises pressure up to roughly tenfold to purge sediment from the pipe.

Workshop note. Waterline front assemblies combine a pressure regulating valve, filter, water meter, and medicator doser to stabilize supply and prevent nipple clogging.

Supply note. Drip cups are molded from PP plastic to catch spillage and keep litter dry; suspension uses 1,500 lb winches with hanging points every 3 m, and galvanized pipe carries at least 275 g/m2 of zinc coating.

The engineering notes above compile verified reference, material and application data for aftermarket poultry equipment and compatible poultry equipment.

Quality & authority

Inspection runs on an AQL sampling plan: incoming material, in-process checkpoints and a final release check are recorded on the batch sheet.

Why choose Vidishi Auto

Poultry Equipment — Poultry Equipment. Supplied under Vidishi Auto with batch traceability and trade-grade packing; volume pricing and private-label options are available on request. Poultry cage systems are supplied for layer-hen and breeding-farm programs.

Shipping & packaging

We ship worldwide to distributors and garages from China, Dongguan. Each Poultry Equipment is packed in a single-unit export carton. Cage components ship stacked and strapped in export cartons for assembly on site. Tracked air or sea freight is arranged per order volume.

Bulk quantities of poultry equipment supplier and poultry equipment bulk order ship in mixed containers from China, Dongguan.

Cross-reference & catalog

Catalog numbering for this Poultry Equipment: the primary reference is PE-V2LA1. When a supplier catalog lists superseded or regional formats, match on the numeric core of the code rather than the prefix, then confirm the physical fit.

Catalog cross-references for poultry equipment catalog and poultry equipment guide resolve to PE-V2LA1.

Frequently asked questions

Further laying hen cage system questions are answered by the trade desk within one business day.

Compliance disclaimer

Vidishi Auto is an independent supplier. This is an aftermarket compatible replacement, not a genuine OEM part. Brand names are trademarks of their respective owners and are used only to identify fitment.

Wholesale & support

Wholesale terms are quoted per market: volume breaks, mixed-SKU containers and private-label options are all handled by the trade desk. Tier layout, wire gauge and assembly documentation is available on request.

Trade desk replies with quotation, MOQ and lead time in one business day.

Enquiries about wholesale poultry equipment and poultry equipment price receive quotations within one business day.

Layout & assembly notes

Cage systems are matched to the house layout; the assembly scope below is confirmed before dispatch.

Installation and service notes for poultry equipment replacement, cornerstone farm poultry equipment and mayura pipes and poultry equipments are confirmed by our technical team before dispatch.

• Pre-dispatch checks: the OE / reference number is matched against your old part before packing.
• Tier layout and capacity are confirmed against your house plan before dispatch.

Workshop teams comparing poultry equipment cross reference, why upgrade poultry equipment and hot-dip galvanized receive the pre-dispatch checklist with the quotation.

• Wire gauge, feeder and water-line scope are confirmed with the quotation.

Installation and service notes for automatic battery cage, chicken cage and hot-dip galvanized poultry cage are confirmed by our technical team before dispatch.

• Components ship stacked and strapped for on-site assembly.

Workshop teams comparing poultry cage receive the pre-dispatch checklist with the quotation.