VDS-FDC-2N Two-Nozzle Fuel Dispenser Controller for FDC-2N
VDS-FDC-2N for petrol, diesel and LPG dispensers. Model FDC-2N, 12 Months warranty, MOQ 1 piece. Supplied under the Vidishi Auto brand.
$250.00
100% Secure Checkout
Free Shipping Over $1099
Customer Satisfaction
International Shipping
Product Specifications
Product Details
At a glance
Check fitment before you order
Built to model FDC-2N and supplied new under the Vidishi Auto brand. The 15 specification rows below run from controller variants through to ex-proof signal; a row is only listed where the value is confirmed for this part.
Part number match
The order reference for this item is VDS-FDC-2N, built to model
FDC-2N. Quote that model number on the order and on the packing
list so the correct variant is picked.
Fitment verification
For oil, LPG and CNG dispensers with one or two nozzles. The nozzle, motor, pump and flow-meter counts must match the controller variant ordered; confirm the dispenser configuration and the supply voltage before ordering, and commission the unit with the dispenser manual in hand.
Read the number stamped on the unit being replaced and the
engine code plate, then compare both with the numbers published on this page
before ordering. This three-step check (part number — engine code plate —
published reference) is how fitment is confirmed.
How fitment is confirmed
Three checks confirm fitment before the order ships: the engine code or the VIN read off the vehicle plate or the machine registration, the part number stamped on the unit being replaced, and a photograph of that unit with the number legible. Where the chassis plate is the only reference available, send the engine code with the enquiry and the match is confirmed from it.
Category
This item sits in the site’s Fuel System > Fuel Dispenser Parts category. Ordering it from this page keeps
the line in one category, so a mixed order covering several nozzle or fuel system
items can be picked as a single shipment.
Specifications
| Controller variants | 1 to 8 nozzles (ZC-11111 to ZC-44488 family) |
|---|---|
| Ambient temperature | -25 C to +55 C |
| Humidity | 90 % or below |
| Flow rate range | 5 – 60 L/min, or 5 – 90 L/min |
| Nozzle control | Automatic shut-off nozzle switching |
| Suction distance | 6 m vertical, 50 m horizontal |
| Accuracy | +/- 0.30 % |
| Repeatability | +/- 0.15 % |
| Hose length | 3 m low hang, 4.5 m high hang |
| Inlet pressure | 54 kPa minimum |
| Outlet pressure | 0.3 MPa maximum |
| Supply voltage | 110 V / 220 V / 380 V, 50 / 60 Hz |
| Motor power | 1 HP (0.75 kW) |
| Noise level | 80 dB(A) or below |
| Ex-proof signal | ExdmbIIAT3 |
| Model number | FDC-2N |
| Reference | VDS-FDC-2N |
| Product type | Fuel Dispenser Controller |
| Supplied brand | Vidishi Auto |
| Reference design | reference only — compatible replacement |
| Application | petrol, diesel and LPG dispensers |
| Material | Enamelled steel enclosure with a coated controller board and wiring loom |
| Condition | New |
| Warranty | 12 Months |
| Minimum order | 1 piece |
| Quality system | CE (supplier declaration) |
Two rows on this table decide most enquiries about the item: controller variants and nozzle control. The remaining 13 rows separate this build from the neighbouring variants in the same family, so a buyer who reads only the first two should still check the rest against the unit being replaced.
Specification rows describe the item supplied under the Vidishi Auto brand. Fitment-relevant values must be confirmed against the unit being replaced; packaged shipping figures are not published because no source states them.
What the buyer gets
The first eight of the 15 published specification rows are set out below. The rest are
in the specification table above.
Controller variants
1 to 8 nozzles (ZC-11111 to ZC-44488 family)
For this this part, that figure decides whether the part can be used at all.
Ambient temperature
-25 C to +55 C
Buyers ask for this one on almost every enquiry, so it is stated rather than buried in the table.
Humidity
90 % or below
A this part from a different model shows itself here, so the unit being replaced is checked against it before fitting.
Flow rate range
5 – 60 L/min, or 5 – 90 L/min
For this this part, that figure decides whether the part can be used at all.
Nozzle control
Automatic shut-off nozzle switching
A buyer checks this on the this part first, because nothing else on the part can be confirmed without it.
Suction distance
6 m vertical, 50 m horizontal
Buyers ask for this one on almost every enquiry, so it is stated rather than buried in the table.
Accuracy
+/- 0.30 %
For this this part, that figure decides whether the part can be used at all.
Repeatability
+/- 0.15 %
The workshop asks for this one before ordering, not after, so it is published here.
How it is used
Sequence
- Isolate the dispenser at the mains and lock it off before the controller is disturbed.
- Note the existing terminal wiring against the diagram printed inside the cover.
- Match the controller variant to the nozzle, motor, pump and meter counts on the dispenser.
- Terminate each core to its labelled position and check the supply voltage selector.
- Commission the dispenser with a measured delivery test before it goes back on the forecourt.
Have these to hand first
- Ferrule and terminal set for the loom
- Fuses to the dispenser rating
- A calibrated measure for the delivery test
The list is what the job consumes, not part of the item supplied
unless a specification row above says so.
or the vehicle service procedure. Torque figures, pressures and safety limits come from the
equipment documentation, not from this page.
Documented limits and things that go wrong
A controller must be matched to the dispenser it drives. The nozzle, motor, pump and meter counts on the order are what make the unit a drop-in part.
Calibration and metrology approval are the operator’s responsibility; commissioning has to be done with the dispenser manual and the local weights and measures rules in hand.
Electrical work on a forecourt is not a DIY job, and the ex-proof classification is void if the housing is not reassembled correctly.
The specification table is the supplier’s own technical parameter block for this controller family: ambient range, humidity, flow rate, suction distance, accuracy, repeatability, hose lengths, inlet and outlet pressures, voltage, motor power, noise, price and volume display ranges and the ExdmbIIAT3 ex-proof signalling.
The CE mark is stated by the supplier and is carried on the page as a supplier declaration.
The variant table (nozzle, motor, pump and meter counts) is published on the page as the selection basis because the controller is ordered by variant.
Symptom and first check
| Delivered volume reads wrong | check the flow meter pulse setting against the controller configuration. |
|---|---|
| Nozzle will not latch | the nozzle switch input is terminated on the wrong position. |
| Controller resets during delivery | supply voltage drops on motor start, so check the supply and the motor rating. |
How we label data on this page
| Model number FDC-2N | Published — stated on the specification table above |
|---|---|
| Product type and application | Published — stated on the specification table above |
| Fitment and duty limits | Confirm before order — must be checked against the equipment the item works on |
| Packaged shipping weight | Not published — no source states it for this exact part |
| Carton dimensions for multi-unit orders | Not published — quoted with the order against the actual quantity |
| Internal component part numbers | Not published — the documentation available for this item does not state it |
| Firmware revision | Not published — the documentation available for this item does not state it |
| Loom length as supplied | Not published — the documentation available for this item does not state it |
confirm. Ratings are stated exactly as the manufacturer documents them; nothing on this
page extends them, and a value we cannot confirm is marked Not published rather than
guessed.
First-use checks
Commissioning sequence
- Unpack and check the item against the specification table on this page.
- Confirm the model number FDC-2N on the packing list matches the item received.
- Read the 15 specification rows that apply to your application before first use.
- Electrical work on a forecourt is a competent-person job, and the dispenser must be isolated and locked off first.
- Commission with a measured delivery into a calibrated measure before the dispenser is returned to service.
- Record the installation date so the inspection interval can be planned.
Before it goes into service
After commissioning, run a measured delivery test and file the result; that record is what proves the dispenser at the next inspection.
Warranty cover runs for 12 Months from delivery on the supplied item.
Where this fuel dispenser controller is used
For oil, LPG and CNG dispensers with one or two nozzles. The nozzle, motor, pump and flow-meter counts must match the controller variant ordered; confirm the dispenser configuration and the supply voltage before ordering, and commission the unit with the dispenser manual in hand.
This fuel dispenser controller is supplied for petrol, diesel and LPG dispensers. The application list below is built from the published fitment data for this part number rather than a generic catalogue sweep, which is why it is shorter and more specific than a parts-finder list.
- Single-nozzle dispenser
- Double-nozzle dispenser
- LPG dispenser
- CNG dispenser
- AdBlue dispenser
- Mobile fuel dispenser
Fitment verification: For oil, LPG and CNG dispensers with one or two nozzles. The nozzle, motor, pump and flow-meter counts must match the controller variant ordered; confirm the dispenser configuration and the supply voltage before ordering, and commission the unit with the dispenser manual in hand.
The application list is a guide, not a guarantee of fit. Confirm the
model number on the unit and the part number being replaced before ordering.
Quality and inspection
CE
Quality system coverage for export and distribution, applied to this batch.
New condition
Supplied new, with 12 Months warranty on the delivered item. The fuel dispenser controller is built to model
FDC-2N and packed against that model number.
Specification count
15 specification rows are listed on this page for the fuel dispenser controller, from controller variants to ex-proof signal.
exact part; anything else is marked Not published rather than guessed.
Related search terms
A buyer searching fuel dispenser controller is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is controller variants: 1 to 8 nozzles (ZC-11111 to ZC-44488 family). That figure is what the order is picked against, so it is quoted on the order line.
A buyer searching two-nozzle fuel dispenser controller is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is ambient temperature: -25 C to +55 C. It appears on the specification table above as well, so page and order agree.
A buyer searching fuel dispenser parts is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is humidity: 90 % or below. The workshop uses it to confirm the item before it leaves the shelf.
A buyer searching car seats and booster seats regulations is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is flow rate range: 5 – 60 L/min, or 5 – 90 L/min. It is the value the test bench has to reproduce before the part is released.
A buyer searching wayne fuel dispenser parts is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is nozzle control: Automatic shut-off nozzle switching. Where the value is not published for this item, the table above says so rather than guessing.
A buyer searching fuel dispenser control system is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is suction distance: 6 m vertical, 50 m horizontal. It separates this build from the neighbouring variants in the same family.
A buyer searching fuel dispenser parts diagram is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is accuracy: +/- 0.30 %. That figure is what the order is picked against, so it is quoted on the order line.
A buyer searching petrol pump fuel dispenser parts diagram is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is repeatability: +/- 0.15 %. It appears on the specification table above as well, so page and order agree.
A buyer searching fuel dispenser parts suppliers is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is hose length: 3 m low hang, 4.5 m high hang. The workshop uses it to confirm the item before it leaves the shelf.
A buyer searching fuel dispenser parts name is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is inlet pressure: 54 kPa minimum. It is the value the test bench has to reproduce before the part is released.
A buyer searching wayne fuel dispenser parts diagram is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is outlet pressure: 0.3 MPa maximum. Where the value is not published for this item, the table above says so rather than guessing.
A buyer searching refrigerator dispenser control board is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is supply voltage: 110 V / 220 V / 380 V, 50 / 60 Hz. It separates this build from the neighbouring variants in the same family.
A buyer searching frigidaire refrigerator dispenser control board is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is motor power: 1 HP (0.75 kW). That figure is what the order is picked against, so it is quoted on the order line.
A buyer searching ge refrigerator dispenser control board is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is noise level: 80 dB(A) or below. It appears on the specification table above as well, so page and order agree.
A buyer searching kenmore refrigerator dispenser control board is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is ex-proof signal: ExdmbIIAT3. The workshop uses it to confirm the item before it leaves the shelf.
A buyer searching lg refrigerator dispenser control board is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is controller variants: 1 to 8 nozzles (ZC-11111 to ZC-44488 family). It is the value the test bench has to reproduce before the part is released.
A buyer searching maytag refrigerator dispenser control board is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is ambient temperature: -25 C to +55 C. Where the value is not published for this item, the table above says so rather than guessing.
A buyer searching samsung refrigerator dispenser control board is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is humidity: 90 % or below. It separates this build from the neighbouring variants in the same family.
A buyer searching whirlpool refrigerator dispenser control board is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is flow rate range: 5 – 60 L/min, or 5 – 90 L/min. That figure is what the order is picked against, so it is quoted on the order line.
A buyer searching ge refrigerator water dispenser control board is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is nozzle control: Automatic shut-off nozzle switching. It appears on the specification table above as well, so page and order agree.
A buyer searching porque el refrigerador hace mucha escarcha is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is suction distance: 6 m vertical, 50 m horizontal. The workshop uses it to confirm the item before it leaves the shelf.
A buyer searching fuel dispenser controller for FDC-2N for single-nozzle dispenser is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is accuracy: +/- 0.30 %. It is the value the test bench has to reproduce before the part is released.
A buyer searching fuel dispenser controller for FDC-2N for double-nozzle dispenser is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is repeatability: +/- 0.15 %. Where the value is not published for this item, the table above says so rather than guessing.
A buyer searching fuel dispenser controller for FDC-2N for lpg dispenser is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is hose length: 3 m low hang, 4.5 m high hang. It separates this build from the neighbouring variants in the same family.
A buyer searching fuel dispenser controller for FDC-2N for cng dispenser is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is inlet pressure: 54 kPa minimum. That figure is what the order is picked against, so it is quoted on the order line.
A buyer searching fuel dispenser controller for FDC-2N for adblue dispenser is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is outlet pressure: 0.3 MPa maximum. It appears on the specification table above as well, so page and order agree.
A buyer searching fuel dispenser controller for FDC-2N wholesale is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is supply voltage: 110 V / 220 V / 380 V, 50 / 60 Hz. The workshop uses it to confirm the item before it leaves the shelf.
A buyer searching fuel dispenser controller for FDC-2N supplier is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is motor power: 1 HP (0.75 kW). It is the value the test bench has to reproduce before the part is released.
A buyer searching bulk fuel dispenser controller for FDC-2N is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is noise level: 80 dB(A) or below. Where the value is not published for this item, the table above says so rather than guessing.
A buyer searching fuel dispenser controller for FDC-2N manufacturer is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is ex-proof signal: ExdmbIIAT3. It separates this build from the neighbouring variants in the same family.
A buyer searching fuel dispenser controller for FDC-2N factory direct is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is controller variants: 1 to 8 nozzles (ZC-11111 to ZC-44488 family). That figure is what the order is picked against, so it is quoted on the order line.
A buyer searching fuel dispenser controller for FDC-2N distributor is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is ambient temperature: -25 C to +55 C. It appears on the specification table above as well, so page and order agree.
A buyer searching fuel dispenser controller for FDC-2N for workshop is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is humidity: 90 % or below. The workshop uses it to confirm the item before it leaves the shelf.
A buyer searching fuel dispenser controller for FDC-2N OEM equivalent is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is flow rate range: 5 – 60 L/min, or 5 – 90 L/min. It is the value the test bench has to reproduce before the part is released.
A buyer searching fuel dispenser controller for FDC-2N export is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is nozzle control: Automatic shut-off nozzle switching. Where the value is not published for this item, the table above says so rather than guessing.
A buyer searching fuel dispenser controller for FDC-2N petrol, diesel and lpg dispensers is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is suction distance: 6 m vertical, 50 m horizontal. It separates this build from the neighbouring variants in the same family.
A buyer searching fdc-2n fuel dispenser controller for FDC-2N is normally matching a job on the petrol, diesel and LPG dispensers, and the deciding check is accuracy: +/- 0.30 %. That figure is what the order is picked against, so it is quoted on the order line.
The search terms above are the type term and its model-qualified form,
collected from the specification table published on this page; each one maps to a
model-number-matched line on the order.
Wholesale and B2B supply
Dispenser controllers for petrol-station contractors, dispenser rebuilders and fuel equipment distributors, with variant matching on the order.
- Minimum order: 1 piece
- Container and consolidated shipment quotes
- Neutral or Vidishi Auto branding options
- Model-number matched picking and packing lists
Request a quote
Send the model number, quantity and destination for a delivered total. Model
FDC-2N, MOQ 1 piece, 12 Months warranty – wholesale, container and
consolidated pricing on request.
Pricing is quoted per order. This page carries no published tariff.
Orders are picked against the model number, packed in export cartons with the image list enclosed, and can be consolidated with other lines from the same category.
Lead time is quoted with the order against the destination and the
quantity, and is confirmed before production starts.
Choosing between options
| Matched controller variant | arrives configured for the nozzle, motor, pump and meter counts on the dispenser |
|---|---|
| Universal board | cheaper, and usually needs wiring changes and a new configuration |
| Full dispenser replacement | the capital route, only economic when the dispenser frame is finished |
For a dispenser the deciding question is the variant: nozzle, motor, pump and meter counts have to match before the controller is a drop-in part.
This comparison describes product categories, not brands. It is a
selection aid, not a performance claim.
Image set
5 images are published for this item, distributed across the modules
above. Every frame is photographed from this product.
Frame by frame: Terminal diagram inside the cover; Board and matched accessory set; Connector sockets at the rear; Case open, loom dressed aside; Terminal block printed on the lid.
The same file names appear in the image list issued with the order.
Frequently asked questions
Is this a genuine the original equipment maker product?
No. It is a compatible replacement supplied under the Vidishi Auto brand to the specification published on this page. It is not a genuine the original equipment maker product and is not affiliated with the original equipment maker. Where a reference part number appears it identifies the equipment being replaced, not an original-equipment product, and no affiliation with the original equipment maker is claimed.
What does model FDC-2N cover?
15 specification rows are published for it, from controller variants to ex-proof signal. The delivered material is Enamelled steel enclosure with a coated controller board and wiring loom and the stated warranty is 12 Months.
How do I confirm this fits before ordering?
Read the model number or the part number stamped on the unit being replaced and compare it with the reference numbers on this page. For oil, LPG and CNG dispensers with one or two nozzles. The nozzle, motor, pump and flow-meter counts must match the controller variant ordered; confirm the dispenser configuration and the supply voltage before ordering, and commission the unit with the dispenser manual in hand.
Do you supply this in wholesale quantities?
Yes. The minimum order is 1 piece, and container and consolidated shipment quotes are available on request.
What warranty applies?
The supplied item carries a 12 Months warranty. Warranty terms are published on the site warranty page.
Which images on this page are of this product?
All of them. Every frame on this page shows this exact item.
What is the lead time on this item?
Lead time is quoted per order against the model number, the quantity and the destination, and it is confirmed on the order acknowledgement before production starts. Consolidated shipments follow the same confirmation.
What happens if it does not fit?
Returns are handled under the site returns policy. Fitment is confirmed by the model number and the number stamped on the unit being replaced before dispatch, which is what keeps a wrong-part return from happening in the first place.
Is a public price shown here?
No. Pricing is quoted per order against model number, quantity and destination. Send those three details and a delivered total comes back.
Support and ordering information
Need this part matched?
Send the model number or the part number stamped on the unit you are replacing, and
we return the matched item with a delivered quotation. Technical answers always
match the specification shown above, so what we quote and what you read here never
disagree.
Fitment is confirmed by model number and stamped part number.
Application lists are a guide, not a guarantee of fit.
Order checklist
- Model number: FDC-2N
- Reference part number: VDS-FDC-2N
- Minimum order: 1 piece
- Warranty: 12 Months
- Brand: Vidishi Auto
Reviews